Best Ispring Water Filter Replacement For Culligan Cartridge
Nowadays, there are so many products of ispring water filter replacement for culligan cartridge in the market and you are wondering to choose a best one. You have searched for ispring water filter replacement for culligan cartridge in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings ispring water filter replacement for culligan cartridge which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
32,348 Reviews Scanned
iSpring WGB21B 2-Stage Whole House Water Filtration System, 4.5"X10" Big Blue, 1" Ports, 1-Set Filter Cartridge Included
- 1″ in & out and 4.5″X10″ blue housings — less water pressure loss.
- Two Stages of filtration – removes up to 95% of VOCs, TOCs, sediment, chlorine, and other contaminants that cause foul tastes and odors.
- 50,000 gallon capacity – replaceable carbon filter provides a full year of clean water for a family of four.
- Easy installation. Opening wrench (for 20″ filter housings) included. Comes assembled with wall mounting bracket
- Pressure release valve (allows for release of built-up pressure when changing filters)
iSpring F22-75 3-Year 75GPD Filter Replacement Supply Set for 5-Stage Reverse Osmosis Water Filtration Systems
- Tested by independent third-party to meet NSF/ANSI Standard, high capacity replacement filters for 5-stage reverse osmosis systems
- Standard sized 10″ x 2.5″
- Fits iSpring RCC7, RCC7P, and most other RO systems that use standard sized filter housings including Flowmatic, PuROLine, Crystal Quest, and Apec
- Includes 6x FP15 sediment filters, 6x FG15 GAC filters, 6x CTO carbon filters, 1x RO membrane, and 3x FT15 post carbon filters
- Each filter is individually wrapped to preserve freshness and extend shelf life
The F22-75 3-year filter pack comes with a total of 22 replacement filters so the filters can be changed on schedule for 3 years.
6x 5 Micron 10″” Sediment Filters (1st Stage, #FP15): Removes dirt, rust, sand, and other particles. Replace approximately every 6 months.
6x 5 Micron 10″” Granular Activated Carbon (GAC) Filters (2nd Stage, #FG15): Absorbs chlorine, halide, organic contaminants, odors, and other impurities that contribute to bad tastes and odors. Replace approximately every 6 months.
6x 5 Micron 10″” CTO Carbon Block Filters (3rd Stage, #FC15): Further removes any remaining chlorine, tastes, and odors. Replace approximately every 6 months.
1x High Rejection .0001 Micron TFC Reverse Osmosis Membrane (4th Stage, #MC7): The heart of the RO system. Produces drinking water at a rate of 75 gallons per day. Replace approximately every 2-3 years.
3x Post Carbon Inline Filters (5th Stage, #FT15): Polishes the water from the tank before it is delivered to the faucet. Replace approximately every 12 months.
This filter pack fits the iSpring RCC7, RCC7P, and most other RO systems that use standard sized filter housings including Flowmatic, PuROLine, Crystal Quest, and Apec.
iSpring FP25X25-5 Micron 20" X 2.5" Sediment Filter Cartridges, Pack of 25
5 Micron high-quality 20″ x 2.5″ Sediment filter cartridges, tested by independent third-party to meet NSF/ANSI Standard.
Product Highlights:
– Individually wrapped, packed in 25 pcs per carton
– Removes dust, particles, and rust
– Good for water filters and aquariums.
– Free tech support before and after sale
– Ship from Atlanta warehouse daily. Only 2-day transit time for most states in Eastern Time zone and part of Central time zone (including Texas) We also carry many other home filter systems. Please check our Amazon store for other items.
iSpring WSP-50 WSP-50-Reusable Spin Down Sediment Water Filter-50 Micron, 20 GPM, 1" MNPT + 3/4" FNPT, Brass
- High impact stainless steel mesh filter screen rated at 50 Micron
- Ideal first layer of filtration before a larger filtration system
- Flushable and reusable, takes considerable workload off finer filters that follow behind it
- helps create a multi-layer gradient filtration system for better filtration results and longer filter life
- See through housing offers easy visual monitoring
- system body with 1-year
- Double threads on both ends: 1 inch MNPT and 3/4 inch FNPT, flush out valve has garden hose barb fitting
The WSP-50 spin down sediment filter is ideal for filtering out course sediment larger than 50 micron. The stainless steel screen makes the flushing and cleaning process very simple, allowing flushing of the contaminants through the bottom of the filter when the cartridge begins to get clogged. This allows the stainless steel filter cartridge to be used over and over again without needing to be replaced. The 1 inch outlet MNPT fitting provides a maximum 20 gpm flow rate, and the WSP-50 also features 3/4 inch NPT threads on the inlet and outlet. The housing is manufactured with FDA approved grade materials.
Specifications:
Mesh pore rating: 50 micron
Dry weight: 1 lb
Dimensions: 3.5″ width x 9″ height
Suitable temperature range: 40 – 100 °F
Suitable pressure range: 20 – 90 psi
iSpring WGB22B-PB Lead Iron Chloride Reducing 2-Stage 80,000 Gal. Big Blue Whole House Water Filter
- Equipped with gradient two stage filtration, iSpring WGB22B-PB whole house water system removes sediment, chlorine, lead, Iron,rust, pesticides, herbicides, industrial solvents, VOCs, and various other contaminants. With 1 inch NPT inlet/ outlet, it has minimum impact on water flow and requires minimum maintenance.
- Installed at the main water supply to treat all the water you use in your entire home. Enjoy better water from every tap and every appliance in the whole house. In addition to the basic features of sediment, chlorine and odor removal, this system also excels in the reduction of Lead and iron residue to protect your home appliances, such as the dishwasher and washing machine and to provide you safe water to drink.
- Unlike an RO system, this system will NOT reduce Total Dissolved Solids (TDS), thus it keeps the healthy minerals in the water.
- The first stage CTO Carbon Block filter uses high quality coconut shell carbon for maximum filtration efficiency and filter life. Both are tested by independent third-party to meet NSF/ANSI Standards. Both filters have a capacity of 100,000 gallon of water to supply one full year of clean water for a family of four.
- The second stage FCRC25B Lead & Iron removal filter features high capacity at 15,000 ppm for lead. Effectively reduces lead to below 15 ppb (EPA standard for drinking water).
- Package includes – black metal bracket, two big blue housings with caps, two filter cartridges, and a 4.5 inch housing wrench.
- The model# of the original filter cartridge pack in the system is F4WGB22BPB, which includes these genuine iSpring Big Blue Filter cartridges: FC25B, FCRC25B.
The WGB22B-PB whole house filtration system is a great “point of entry” filtration system for cleaning up well water. Unlike “point of use” systems (like reverse osmosis systems) that are installed to supply water to a specific faucet, the WGB22B-PB filters your water from the source. This means water from every output in your home will have passed through the two filtration stages of the WGB22B-PB. So what exactly do these two stages of filtration offer?
The first stage of the WGB22B-PB houses a 5-micron CTO coconut shell carbon block filter. Block carbon is more effective than other forms of carbon in that it is finely ground up carbon packed into a solidified block. This means they have a higher density than other types of carbon filters, and are therefore more effective in removing their targeted contaminants. The carbon block filter knocks out bad tastes and odors, removes over 90% of chlorine from the water, and is highly effective on organic chemicals (VOCs) like pesticides, herbicides, and industrial chemicals.
The second stage of the WGB22B-PB houses an iron and lead reducing filter. The FCRC25B iron and lead reducing filter is only included with the WGB22B-PB (and the WGB32B-PB), as it is not needed for most municipal water supplies that the WGB22B targets.
If you are on municipal (city) water or a generally clean water supply, you may want to consider the WGB22B over the WGB22B-PB. For removing contaminants and heavy metals like lead and iron found in the majority of well water supplies however, the WGB22B-PB fits the bill.
*Note* The lead & iron reducing filter #FCRC25B’s capacity for iron is much lower than the capacity for lead. Depending on the amount in your water, the filter may lose effectiveness in removing iron before the life of the filter expires. If iron is the main concern, you may instead want to look at using a filter specifically for iron such as the #FM25B, which is also included in our whole house systems #WGB22BM and #WGB32BM.
iSpring Whole House 3-Stage Water Filter System with Oversized Fine Sediment and Double Premium Carbon Block, WCB32O
- Equipped with gradient three stage filtration, iSpring WCB32 whole house water system removes sediment, chlorine, rust, pesticides, herbicides, industrial solvents, VOCs, and various other contaminants.
- Installed at the main water supply to treat all the water you use in your entire home. Enjoy better water from every tap and every appliance in the whole house.
- Unlike an RO system, this system will NOT reduce Total Dissolved Solids (TDS), thus it keeps the healthy minerals in the water.
- The first stage high capacity polypropylene sediment filter achieves filtration down to 5 microns. The second and third stage CTO Carbon Block filter uses high quality coconut shell carbon for maximum filtration efficiency and filter life. Both are tested by independent third-party to meet NSF/ANSI Standards.
- It comes with a 3/4” NPT inlet and outlet and accepts 20” x 2.5” water filter cartridges that can purify up to 35K gallons of water before filter replacement. (6 months). Package includes – Metal bracket, three housings with caps, three filter cartridges, a housing wrench and a manual.
The WCB32 whole house filtration system is the ideal “point of entry” filtration system for cleaning up water supplies to a home or business on municipal (city) water. Unlike “point of use” systems (like reverse osmosis systems) that are installed to supply water to a specific faucet, the WCB32 filters your water from the source. This means water from every output in your home or business will have passed through the three filtration stages of the WCB32. So what exactly do these three stages of filtration offer? Used as the first stage of defense on the system, the stage 1 housing holds a 5-micron high-capacity polypropylene sediment filter. This filter removes dirt and other various larger sized particles from the water that can clog the following filters. The second and third stages of the WCB32 house 5-micron CTO coconut shell carbon block filters. Block carbon is more effective than other forms of carbon in that it is finely ground up carbon packed into a solidified block. This means they have a higher density than other types of carbon filters, and are therefore more effective in removing their targeted contaminants. The carbon block filters knock out bad tastes and odors, combine to remove over 90% of chlorine from the water, and are highly effective on organic chemicals (VOCs) like pesticides, herbicides, and industrial chemicals. If you are on well water or have unusual contaminants in your municipal water supply, you may want to consider the WGB32BM over the WCB32. For removing the common contaminants found in the majority of municipal water supplies however, the WCB32 fits the bill.
iSpring HC16 Whole House Transparent Water Filter Housing 10-Inch 3/4-Inch FNPT Inlet/Outlet with 1 x 5 Micron Sediment Filters
- Size: 3/4″ Stainless Steel Reinforced Inlet/Outlet Connectors
- Fits 10″x2.5″ Standard Filter Cartridges
- Helps Protect Residential Appliances and Home Pluming from Sediment, Rust, Scale, Dirt, Coarse Sand, Sand, Silt, Bad Taste, Odor, Aesthetic and Chlorine Taste (depending on filter cartridge)
- Tested by Independent Third-Party to Meet NSF/ANSI Standard
- Lifetime support from iSpring in Alpharetta, GA at (678) 261-7611
Typically the first stage for any water filtration system, the sediment filter removes dirt, particles, and rust. Made of 100% melt-blown polypropylene, 4-layer filtration. Depending on your water usage and quality, it should be replaced every 3-6 months. Tested by independent third-party to meet NSF/ANSI Standard. Genuine iSpring filter sold directly by manufacturer. Performance and quality guaranteed. Fits standard 10 inch filter housings, including most name brand models. Well packed for freshness – Each cartridge is individually wrapped with manufacturing date.
iSpring WSP-50SL Reusable Spin Down Sediment Filter/w Siliphos, Alternative Descaler or Softener, Hot Water System Protector, 50 Micron
- High impact stainless steel mesh filter screen with a pore size of 50 microns. The ideal first line of defense for finer filters, or expensive plumbing appliances.
- Includes Siliphos to help prevent scale and stop corrosion, greatly extending the life of your plumbing fixtures. It is recommended that the filter to be replaced every 3-6 months to prevent scale from building up.
- Includes Siliphos to help prevent scale and stop corrosion, greatly extending the life of your plumbing fixtures. It is recommended that the filter to be replaced every 3-6 months to prevent scale from building up.
- See through housing offers easy visual monitoring
- Stainless steel body with 1-year warranty. Lifetime support from iSpring in Alpharetta, GA at (678) 261-7611
- Double threads on both ends: 1 inch MNPT and 3/4 inch FNPT, flush out valve has garden hose barb fitting
The ideal water filter system includes a sediment filter as the first stage to remove the larger particles of dirt or sediment before they can reach and clog your finer filters and appliances. The WSP-Series aims to fill this role by offering the stainless steel mesh in various micron sizes, allowing you to control what size particles are allowed to pass into your home or following filters. This helps prevent large particles of dirt from clogging any finer filters you may already have in place. The WSP also includes a powerful anti-scale and corrosion agent called siliphos. Siliphos is a water treatment compound, a glass-like Polyphosphate containing Sodium, Calcium Magnesium and Silicate, formulated specifically for the treatment of water problems. The 1-inch outlet MNPT fitting provides a maximum 20 GPM flow rate, and the WSP-Series also features 3/4 inch NPT threads on the inlet and outlet. The housing is manufactured with FDA approved grade materials. Specifications: Mesh pore rating: 50, 100, 200, 500, 1000 microns Dry weight: 1 lb Dimensions: 3.5″ width x 9″ height Suitable temperature range: 40 – 100 °F Suitable pressure range: 20 – 90 psi
iSpring US31 3-Stage Under Sink High Capacity Tankless Drinking Water Filtration System-Includes Sediment 2X CTO Carbon Block Filters (Newest Version)
- Up to 20X more effective than the common water pitcher dispenser , Feed Water Temperature – 40-100 F
- Universal 10 inch sediment filter and 2 x 10 inch Carbon block filters
- Removes sediment, chlorine, organic chemicals (VOCs) and more to produce colorless, tasteless and odorless purified water
- Manufactured to comply strictly with FDA standards and tested by independent third party against NSF/ANSI standards (42, 53, 61) for water quality, material safety and structural integrity
- Easy DIY installation.
iSpring GA1-BN Heavy Duty Non-Air Gap Drinking Faucet for Water Filtration, Reverse Osmosis Systems-Brushed Nickel-Contemporary Style High-Spout
- European designer lead-free solid brass faucet. 360 degree free swivel
- Non “air gap” drinking water faucet. NOT a regular hot and cold water kitchen sink or bar sink faucet
- Ideal upgrade for undercounter water filters and reverse osmosis systems
- Brushed Nickel finish. May come with Quick Fitting or Jaco Fitting
- The front washer is pre-installed underneath the metal plate
- Backed by 3-year Manufacturer Warranty with lifetime support line 678-261-7611 from Alpharetta, GA USA
An elegant lead-free European style water filter faucet or Reverse Osmosis system faucet will add a great accent to your kitchen.It features a smooth quarter turn handle with a ceramic seat for a lifetime of service. A 1/2-Inch hole is all that is needed for the faucet stud (all series), but a cover plate with 2 inches Diameter is included to accommodate larger pre-drilled holes.It is 11.25-Inch tall and has a swivel spout with a reach of 6.5-Inch.
The adapter included in the package is for 1/4” tubing only. Please contact us if you need an adapter for 3/8” tubing. Backed by 3-year Manufacturer Warranty with lifetime support line 678-261-7611 from Alpharetta, GA USA.
NOTE:
Not to be used with RO systems that require an Air gap faucet which has three connections on bottom of faucet.
NOT a regular hot and cold water kitchen sink or bar sink faucet.
No hose included
Conclusion
By our suggestions above, we hope that you can found ispring water filter replacement for culligan cartridge for you.Please don’t forget to share your experience by comment in this post. Thank you!