The 10 Best Ice Maker Supply Valve

This Eastman 60232 Sweat Pre-assembled Ice Maker Outlet Box is designed for recessed residential applications. It has a 1/2 inch Sweat inlet connection and a 1/4-inch OD compression outlet with a rough opening of 5-3/4-inch width x 4-7/8-inch height x 3-1/2-inch diameter.

The outlet box comes complete with a pre-installed 1/4-turn ball valve, support bracket, and a faceplate cover of dimensions 8-1/4-inch width x 7-5/16-inch height. It is built with one-piece box and flange design. Valves governed by this Standard are intended for service at temperatures between 34⁰ F (1⁰ C) and 180⁰ F (82⁰ C), with an allowable working pressure rating not less than 125 PSI (862 kPa).

Get your appliances set up quickly and easily with this ice maker, humidifier, water filter and evaporative cooler installation kit. Poly tubing is durable and reliable, and will not ruin the fresh taste of your water. This complete installation kit includes everything necessary for installation, plus step-by-step instructions to make D-I-Y installation a breeze. Best of all, there’s no need to shut off your water supply during installation. Limited lifetime warranty. Make it yours today!

The SharkBite ice maker installation kit has everything you need to install the water supply to your ice maker. The kit includes 1 SharkBite 1/2 in. Service slip tee, one 1/2 in. X 1/4 in. (3/8 in. O.D.) push-to-connect angle stop valve, a 10 ft. Coil of 1/4 in. Pex pipe, one 1/4 in. (3/8 in. O.D.) SharkBite x 1/4 in. O.D. Compression connector, and a 1/2 in. And 1/4 in. Disconnect clip to remove the pipe from the fitting if needed. The SharkBite service slip tee allows you to remove up to 2 in. Of your existing copper or cpvc line and add an angle supply stop valve. Just insert the pipe and the stainless steel teeth bite down and grip tight, while a specially formulated O-ring compresses to create a perfect seal. Disassembly is just as fast using the simple disconnect tool so fittings and valves can be easily changed and reused. They can even be rotated after assembly for easier installation in tight spaces. The included 10 ft. Pex coil connects to the push-to-connect angle stop valve 1/4 in. Outlet and the 1/4 in. Ice maker connector which will thread onto your ice maker. The pipe can be cut to the exact length needed so there is no excess supply line to coil providing a clean, tangle free look.

Metpure EZROADP14 water supply valve allows users to connect and disconnect 1/4″ water supply outlets quick and easy without the need of any other tools. Applications include reverse osmosis drinking water, multimedia filters, beverage dispensing, coffee machines, RV and Marine, misting systems, ice makers and many more.

Product description

Highlights: For installation of humidifiers iice makers and evaporative coolers Include 1/4 x 25 poly tubing, and self piercing saddle valve 1 Kit/Polybag.

From the Manufacturer

LDR 509 5100 Ice Maker/Humidifier Installation Kit , 1/4-Inch X 25-Foot, Poly Tubing. 1/4-Inch X 25-Foot Ice Maker/Humidifier Installation Kit With Poly Tubing includes tubing, self-piercing saddle valve and fitting. Install ice maker or humidifier without turning water off.

Frizzlife feed water valve. White polypropylene with food grade EPDM o-rings, connects between valve and riser to the main water supply line for application in reverse osmosis, filtration systems, automatic coffee brewers, and ice-makers. Not for use with compressed air, explosive gases, petroleum spirits and other fuels, or for heating systems. Sizes indicated are thread male compression x thread female compression x tube OD. Including: TEE UNION ADAPTER: Size: 3/8″ Thread male x 3/8″ thread female x 1/4″ tube quick connect with compression. Fitting A : 1/2″ male NPT and 3/8″ female NPT threaded connections Fitting B: 3/8″ male NPT and1/2″ female NPT threaded connections If your water angle valve is 1/2″ OD, use both TEE union adapter and two fittings to connect the angle valve and water hose. If your water angle valve is 3/8″ OD, only use the Tee union adapter to connect the angle valve and water hose. Water Systems feed water angle stop valve adapter has 3/8” male and female compression and two NPT thread 3/8″ to 1/2″ converter fitting for easy installation on most under-sink cold water supply and faucet water lines. The ¼” Tube OD quick connect fitting allows for easy connection to reverse osmosis systems water filter, ice makers and other potable water applications.

Product Description

This Fluidmaster Braided Stainless Steel 5-Foot (60 in) Length Ice Maker Supply Line connects your Icemaker to the wall water supply. Fluidmaster Icemaker water supply connectors are built to last. Made of a tough polymer core covered with braided stainless steel wire, these connectors exceed every code requirement in the book for durability. Fluidmaster offers a wide variety of types and sizes, perfect for your home improvement efforts. A proven supply line that won’t crease or tangle even in the tightest of corners. Durability and ease-of-use were at the forefront of this design, with the nickel plated brass hex nuts for easy to grip tightening. A 1/4-Inch female compression thread by 1/4-Inch female compression thread connector with an efficient flow rate. Code approved with a 5 year warranty.

From the Manufacturer

Fluidmaster is the #1 toilet repair brand in the world. Fluidmaster parts are found in more toilets than all other brands. The customer’s first choice and preferred supplier of toilet tank trim since 1957. Fluidmaster’s complete line of toilet repair parts includes; fill valves, flush valves, flappers, tank levers, dual flush valves, bowl wax, toilet repair kits, seals, connectors and more. With manufacturing facilities across the world, Fluidmaster reaches over 90 countries worldwide with unparalleled quality.

This Eastman 60233 Pex Pre-assembled Ice Maker Outlet Box is designed for recessed residential applications. It has a 1/2 inch Crimp PEX inlet connection and a 1/4-inch OD compression outlet with a rough opening of 5-3/4-inch width x 4-7/8-inch height x 3-1/2-inch diameter.

The outlet box comes complete with a pre-installed 1/4-turn ball valve, support bracket, and a faceplate cover of dimensions 8-1/4-inch width x 7-5/16-inch height. It is built with one-piece box and flange design. Valves governed by this Standard are intended for service at temperatures between 34⁰ F (1⁰ C) and 180⁰ F (82⁰ C), with an allowable working pressure rating not less than 125 PSI (862 kPa).

Product Description

The Eastman 48398 Ice Maker Installation Kit is the perfect solution for any household. It includes a 15 Feet tube which is made of high-quality copper that provides strength and durability. The 15 ft. roll of copper tubing can be cut to length for a perfect fit.

The kit is universal which fits many major refrigerator brands with ease and provides water to ice-makers, ice and water dispensers. The package includes 15′ copper water supply line, 1 self-piercing saddle valve and union, and a female flare x comp adapter. The Eastman Icemaker Installation Kit includes everything you need to connect a water line to your icemaker.

From the Manufacturer

Eastman’s 15′ Copper Installation Kit includes everything you need for easy installation. The kit fits most refrigerators and provides water to icemakers, ice and water dispensers. Packaging includes a 15′ copper water supply line, 1 self-piercing saddle valve and union, and a female flare x comp adapter. Additional installation hardware is included.

Whirlpool Whirlpool Refrigerator Icemaker Ice Maker & Water Valve 61005273

Conclusion

By our suggestions above, we hope that you can found ice maker supply valve for you.Please don’t forget to share your experience by comment in this post. Thank you!